|
Now, replacing elements can be as easy as changing a light bulb |
|||
|
Unique in design and universal in application. The ESE element provides a breakthrough technology for applications, which could benefit from broad range infrared dispersement.
TYPE: ESE WATTAGE: 60; 100; 150; 200; 250; 350; 500 VOLTAGES: 120 up to 240V
AVAILABLE ACCESSORIES: ESE/R – Spun aluminum reflector ESE/H – Porcelain holder ESE/G – Wire guard ESE/RHG – Complete set (reflector, holder and guard)
|
|
||
|
|
MOBILE UNITS Infrasoft: Hand Mobile This is an extremely versatile unit that can be hand held or mounted in two alternative positions on a special triangular framework that is supplied. Fitted with an SWB/I that holds a SALAMANDER 650W emitter. The unit comes completely wired with an extension lead and 13 amp plug for immediate operation.
Mobile Mark IV An “H” section base is supported by 4 nylon ballrace castors (2 braked). Constructed of 40x40 mm square tube to which is fitted a detachable upright 9cm high with a further internal extension of 32x32 mm square tube extending to 1.9 m (6’) high. Attached to the extension upright by special bracket is a SWB/3 projector fitted with 3x3 50 watt emitters. Both units are fully adjustable in the vertical sense and have plastic knobs to control the forward angles. They are fully wired with a two; position switch and male input three; point socket attached to the loom. The entire unit is electroplated and comes complete with 6 meter coupled extension lead.
|
|
|
|
TYPE SWB : Wide beam heavy; duty industrial projectors fitted with either FTE, FFE, HTE, or HFE type emitters. Both the reflector and outer case are manufactured from 20 gauge aluminized steel. The units are pre; wired and are suitable for applications operating in free air. (70ºF).
|
|
||
|
|
TYPE SWB/R/A: Reflector only with terminal block and mounting studs. Can be fitted with either FTE, FFE, HTE, or HFE emitters.
|
||
|
TYPE CRP 12 X 12: A heavy; duty ceramic infrared panel for use as a single unit or in multiples. The panel and reflectors are manufactured from 20 gauge aluminized steel. The panels are insulated with ceramic fiber insulation and are pre-wired and assembled with LTE emitters. Specify voltage, wattage, and phase when ordering. |
 |
||
|
**RATED 96% INFRARED ENERGY EFFICIENT **ESTIMATED LIFE IN EXCESS OF 10,000 HOURS
|
|||
|
|
TYPE FTE
Full Trough Emitter Recommended irradiation interval of 8” (200mm). Wattages: 150; 200; 250; 300; 350; 400; 500; 600; 650; 750; 800; 1000 |
||
|
TYPE FFE Full Flat Emitter Recommended irradiation interval of 4” (100mm). Wattages: 150; 200; 250; 300; 350; 400; 500; 600; 650; 750; 800; 1000 |
|
||
|
|
TYPE HTE
Half Trough Emitter Recommended irradiation interval of 8” (200mm). Wattages: 100; 125; 150; 200; 250; 300; 325; 400; 500
|
||
|
TYPE HFE Half Flat Emitter Recommended irradiation interval of 4” (100mm). Wattages: 100; 125; 150; 200; 250; 300; 325; 400; 500 |
|
||
|
|
TYPE HSE
Half Square Emitter Recommended irradiation interval of 4” (100mm). Wattages: 150; 200; 250; 300; 350; 400; 500; 650; 800; 1000 |
||
|
TYPE LTE
Large Trough Emitter For special applications and also used in the CRP panel Wattages: Made to order. Contact Factory |
|
||
|
¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ |
|||
|
|
THERMOCOUPLES
A unique spring formed thermocouple Specifically for the salamander emitter. The thermocouple is removable allowing it to be interchanged between emitters. J-24-A Type J K-24-A Type K Cast-in thermocouples available upon request. |
||
|
EMITTER MOUNTING
Our custom designed single piece clip allows for easy mounting and a reduction in the parts required for assembly. The original two piece clip is still available upon request. |
|
||
